|Hales Rifle Grenade (No 3, No 20, No 24, No 35)|
|Type||Percussion cap grenade|
|Place of origin||United Kingdom|
|Used by||United Kingdom|
|Wars||World War I|
|Weight||1 lb 5 oz (No 3), 1 lb 8 oz (No 20 Mk I)|
|Filling||Tonite and TNT for the No 3, Ammonal for No 20 and grenades based on it.|
|Percussion cap fuse|
Operation[edit | edit source]
To fire the No 3, the user must fit the grenade into the rifle, insert the detonator, lay the rifle on the ground in the correct position, remove the safety pin, pull back the safety pin collar, insert a special blank round into the rifle, then fire.
Operation variants[edit | edit source]
With variants that lack the vale, the grenade is activated exactly the same way as the ones that have a vale, but the user does not need to remove the safety pin collar, as it lacks one.
History[edit | edit source]
In 1907, Martin Hale developed the rod grenade. "A simple rod was attached to a specialized grenade, inserted into the barrel of a standard service rifle and launched using a blank cartridge." Unfortunately, the British did not immediately adopt the idea and entered World War I without any rifle grenades. However, as soon as the trench warfare started, there was a sudden need for rifle grenades. The British government purchased a rodded variant of the No 2 grenade as a temporary solution.
By 1915, Hales had developed the No 3, which is commonly known as the Hales Rifle Grenade. The Hales grenade was improved throughout World War I to make it more reliable and easier to manufacture. However, production of the grenade was slow. In order to speed rod grenades to the front, the British also made rodded versions of the Mills bomb.
Although a simple approach, launching a rod grenade "...placed an extreme amount of stress on the rifle barrel and the rifle itself, resulting in the need to dedicate specific rifles to the grenade launching role, as they quickly became useless as an accurate firearm. This led to the search for an alternative and resulted in the reappearance of the cup launcher during the latter years of World War I." After World War I, the rod-type rifle grenade was declared obsolete and the remaining Hales were replaced with Mills Bombs shot from a rifle via a cup launcher.
Variants[edit | edit source]
The Hales went through many variations in order to make it more cost effective and effective.
No 3[edit | edit source]
The No 3 had quite a few problems; first off, it was difficult to manufacture, as it requires precision and is made up of many parts. Another problem occurred with the detonators; like the No 1 Grenade, the No 3 needed a special detonator that was difficult to manufacture. This detonator was also used in the No 2 grenade and was very similar to the one in the No 1 Grenade, which made it even harder to mass-produce.
Operation-wise, the vane was a significant problem; it was hard to align properly and any sort of weather fluctuation, such as rain, strong winds or even a particle of dust could prevent the vane from operating correctly, which caused a failure.
The No 3 also had an overly-sensitive percussion cap, which caused many premature detonations.
Once these problems became well-known, development teams set off to fix these solutions. The No 20 was the result of these refinements.
No 20[edit | edit source]
The No 20 is similar to the No 3, but its main feature is that it lacks the No 3's vane. In theory this was supposed to make it more reliable than the No 3 and it would've worked were it not for the explosive that was put in it. Instead of Tonite or TNT, the No 20 used Ammonite, which tended to corrode the brass parts of the grenade, which created quite a few failures when the grenade was fired.
While improved from the No 3, the No 20 was not perfect, and the No 24 was introduced to address some of the remaining problems.
The No 20 has two variants, the Mk I and II. The Mk I has a solid steel cylinder body very similar to the No 3, while the Mk II uses a weldless steel tube and has circumferential grooves for fragmentation.
No 24[edit | edit source]
The No 24 is essentially a No 20 with a less sensitive percussion cap and refined ammonite that does not corrode the brass parts of the grenade.
Even then, there were still some improvements that could be made, and in 1918 the No 35 was introduced.
There are two variants of the No 24, the Mk I and II. The Mk I uses the No 20 Mk II's body, while the Mk II is uses a cast iron body that has no external grooves.
No 35[edit | edit source]
References[edit | edit source]
- Ainsile, "Hand Grenades" p.6 .
- Ainsile, "Hand Grenades" p.24.
- Saunders, Weapons of the Trench War, p.99
- Saunders, Weapons of the Trench War, p.97
- Saunders, Weapons of the Trench War, p.98
- Saunders, Weapons of the Trench War, p.100
[edit | edit source]
|This page uses Creative Commons Licensed content from Wikipedia (view authors).|